The living room at my parents’ house sits at the far corner of a two-story house with cinder-block walls, and the router is upstairs at the other end. For years that room pulled 10 to 20 Mbps on a good day, and on a bad day the TV wouldn’t connect at all. They just stopped using it. I bought this TP-Link extender in November 2019, ran it for two years, and it’s the reason that room works. If you’re trying to figure out how to set up a TP-Link WiFi extender, here’s the honest version: the setup steps are easy and the placement is everything.
As an Amazon Associate I earn from qualifying purchases. I bought this product myself and this is my own experience with it.
Verdict: the cheapest fix that actually worked
Two years of service, zero failures, and a dead room that went from unusable to streaming everything without a stutter. That’s the whole case for the RE300. It’s the cheapest of the three TP-Link devices in this article by a wide margin, and it’s the one I’d hand to anyone who just wants the far room to work this weekend. check current price on Amazon
Would I buy it again at full price? Yes — if I were going the cheap route and just wanted connectivity fixed now. I wouldn’t buy it if I could run a cable, and I’ll explain exactly why below.
- What held up: two years, no dropouts, no reboots, no dead unit.
- 150 to 200 Mbps in a room that had been getting 10 to 20.
- Set up once and never touched again — my parents never had to think about it.
- Cheapest of the three devices I tried, by a lot.
- What didn’t: it repeats what it catches, so the far room gets a slice of the router’s speed, not all of it — that room topped out around 150 to 200 while the router’s own room was pulling a gigabit.
- It only works if you put it in the right spot. Plug it into the dead room and it’s a paperweight.
Why I bought it
Nothing was there before. No extender, no mesh, no second access point — just a router upstairs and a living room on the wrong side of two flights of wraparound stairs and a lot of block wall. My parents had effectively given up on that TV. That’s the part that made it worth doing: not “faster internet,” but a room in their house they’d written off.
I also bought the matching TP-Link router at the same time so the two could form OneMesh — one network name instead of a second SSID you have to manually switch to when you walk across the house. If you’re buying one of these, buy it into that ecosystem. It’s the difference between a network and two networks that happen to be near each other.
Two years of using it
The number I care about most: 10 to 20 Mbps before, 150 to 200 Mbps after. Same room, same router, same ISP. The room where the router lives was pulling a gigabit down the whole time, which tells you the ceiling wasn’t the connection — it was the walls.
Streaming stopped being a negotiation. Before the extender, my parents didn’t want to watch anything in the living room because it wouldn’t load. After, they watched whatever they wanted at good quality, and I never got a call about buffering. No throughput issues, no dropouts, nothing to troubleshoot.
It ran two years without me touching it. When I eventually replaced the setup, the extender didn’t die or degrade — it came home with me and now sits in a box in my house as a spare, because I couldn’t bring myself to throw away something that worked that well.
How to set up a TP-Link WiFi extender (the part that decides everything)
The pairing itself is a few minutes: plug it in near the router, join its setup network, pick your Wi-Fi, done. The thing that decides whether it works is where it ends up living, and almost everyone gets this wrong.
Don’t put it in the room with bad signal. That’s the instinct and it’s backwards. The extender has to catch a strong signal before it can repeat one — think of it like a bouncy ball. You want to catch the ball at full speed and throw it farther, not catch it after it’s already bounced to a stop in the far corner.
Put it roughly halfway between the router and the room you’re trying to reach. In my parents’ house that meant a hallway outlet mid-house, not the living room. Same device, same walls — placement alone was the difference between 10 Mbps and 150.
Use a Wi-Fi analyzer app on your phone to pick the spot. Walk toward the dead room and watch the signal strength and ping, then stop where it’s still strong and plug in there. It takes ten minutes and it’s the entire job.
What I’d change
Nothing broke, and nothing about the hardware annoyed me. The honest limitation is physics: a repeater re-broadcasts what it catches, so the far room gets a fraction of the router’s throughput, and every hop costs you. For streaming on a TV that’s completely fine. For anything that wants the full pipe — big transfers, a desktop, a NAS — it isn’t, and no amount of careful placement fixes that.
That’s why I moved on. Not because it failed, but because it was the best version of a compromise I no longer needed to make.
The upgrade that beat it: powerline
My house has the same thick walls, so I eventually went a different direction: a TP-Link powerline kit, which pushes the network over the house’s electrical wiring instead of through the air. One adapter plugs in near the router, the other goes in the far room, and the second one broadcasts Wi-Fi from there. see the powerline kit on Amazon
It’s a different class of result. Where the extender got the far room to 150 to 200 Mbps, the powerline kit got the full speed across the house. If your house has reasonably modern wiring, it’s not close.
Two caveats, both from living with it. First, if the power goes out, the two adapters can lose sync with each other and need re-pairing. That’s the one recurring annoyance and it takes a minute, but it’s a minute you’ll spend at some point. Second, on an older house with tired wiring, pushing high speeds over the circuit can be a problem — worth knowing before you buy rather than after.
The router I’d buy again tomorrow
The other half of this is the router, and it’s the single best piece of networking gear I own. I have two of them — one at my parents’ house and one at mine — and the range is absurd. Mine covers my whole house through the same thick walls that killed the old setup. current price and specs on Amazon
Before it I had an older TP-Link two models down, and that thing was a dog. The AX73 has never given me a single issue. Sitting in the same room as it, maybe 10 to 15 feet away, on fiber, I get exactly what my provider hands me — about 450 up and 450 down on a 300 Mbps plan. Same speed up as down, no drama.
The mesh part is what makes the whole ecosystem worth staying in. With the router and the extender on OneMesh, there’s one network name — you don’t walk to the other side of the house and have to connect to Wi-Fi number two. I later added an outdoor access point on the outside of the house, powered off a PoE switch, and that’s covered in my EAP225-Outdoor review.
Is TP-Link going to be banned in the US?
This comes up every time I mention the brand, so here’s what’s actually true. In 2026 the FCC banned consumer routers produced wholly or partly outside the US from getting new approvals. Plenty of makers got exemptions — Netgear, Asus, Amazon’s Eero, Starlink among them. TP-Link hasn’t, so it currently can’t sell its newest Wi-Fi 8 models here.
Models approved before the ban can still be sold, and existing units keep working. That covers both the extender and the router in this article. TP-Link says its existing products remain available in the US. Separately, four states sued the company in October 2026 over its ties to China; TP-Link calls the suits “built on false premises.” None of that changes what’s plugged into my wall.
Key specs
| RE300 extender | Archer AX73 router | WPA7817 powerline kit | |
|---|---|---|---|
| Job | Re-broadcasts Wi-Fi into a dead room | Main router | Carries the network over house wiring |
| Wi-Fi class (as listed) | AC1200 dual-band, up to 1,200 Mbps | AX5400 Wi-Fi 6 dual-band | AV1000 adapter + AX1500 extender |
| How it reaches the far room | Wireless, repeated | Its own radios | Over the power circuit, then Wi-Fi |
| Coverage claim (as listed) | Up to 1,500 sq ft, 25 devices | “Long range coverage” | Not stated |
| Mesh support | OneMesh | OneMesh | EasyMesh, plug and pair |
| What it replaced for me | Nothing — there was no signal | An older TP-Link two models down | The RE300 |
Who should skip it
Skip it if you can run a cable to the far room — a wire beats every device in this article, and it always will. Skip it if the room needs full speed rather than enough speed to stream, because a repeater will always cost you throughput. And skip it if your house has decent wiring and you can afford the powerline kit, because that’s the better answer for the same problem.
FAQ
Does a Wi-Fi extender slow down Wi-Fi?
Yes, at the far end. A repeater catches the router’s signal and re-broadcasts it, so the room it serves gets a fraction of what the router is putting out. In my case the router’s own room pulled a gigabit while the extended room landed at 150 to 200 Mbps. That’s plenty for streaming and completely fine for a TV.
How do I boost Wi-Fi in a house with thick walls?
Place the extender halfway between the router and the dead room, not in the dead room, and use a Wi-Fi analyzer app to confirm the signal is still strong where you plug it in. If the walls are cinder block and the run is long, a powerline kit will beat any repeater because it doesn’t have to cross the walls at all.
Is a powerline adapter better than a Wi-Fi extender?
For me, yes — full speed across the house instead of a slice of it. The tradeoffs are that the adapters can lose sync after a power cut and need re-pairing, and that older house wiring may struggle at high speeds. In a newer house with decent wiring, I’d go powerline first and keep the extender as the cheap fallback.
Bottom line
If you have one dead room and a small budget, the RE300 is the right buy — two years of mine never missed, and careful placement turned 10 Mbps into 150. If you can run a cable or your wiring is good enough for powerline, do that instead and keep this in a drawer as the spare. Either way, buy into the same TP-Link mesh ecosystem so everything stays on one network name.