I installed these fittings on my 1998 Corvette in January 2022, and they have been on the car for close to five years. Before that, transmission fluid was weeping onto the radiator support at about a drop a day, and on a car that gets driven hard that is the kind of slow leak that sits in the back of your head. This Hayden 390 transmission line fitting kit review comes from an actual install on a C5 — 4L60E, auxiliary cooler, 3,000 RPM lockup converter — not from a parts catalog.
As an Amazon Associate I earn from qualifying purchases. I bought this product myself and this is my own experience with it.

Verdict: the fastest fix for a leaking transmission cooler line
Two brass fittings for about the price of lunch, and they turn a clamped-over-the-flare mess into something that looks like a shop did it. On my car they fit everywhere with zero drama and have not leaked in nearly five years. If you are adding an auxiliary cooler to a GM transmission and you want to keep running ordinary rubber hose and clamps, this is the shortest path from ugly to clean. I would buy them again at full price without thinking — they were cheap to begin with.
- What held up: nearly five years on the car, still dry at both fittings
- Threaded straight into the stock cooler ports — no adapters, no drilling
- Pulled transmission temps from 200°F+ down into the 160s–180s
- Cheap enough that buying them took no deliberation at all
- What didn’t / annoyed me: nothing fit-wise — but they only solve half the job, and the hose and clamps are still yours to get right
- Plain rubber hose is the real weak link, and it will weep eventually
- If you want a full AN look, these are the wrong part
Why I bought it
Before this I did what everybody does. I pulled the threads back, pushed the hose over the factory fitting and clamped it down. It leaked about a drop a day. That does not sound like much until you remember it is dripping near a hot radiator and a transmission running over 200°F, and every time you park you are leaving a spot on the ground and wondering how long before it gets worse. The radiator side never looked right either. It worked, sort of, but it looked like something bolted on in a driveway.
The correct alternative is AN-6 line and fittings. That is the right answer if you want a show-quality engine bay, but it means hose ends, adapters, and a cutting and assembly job. These do the same job with a wrench in about ten minutes.
What four years and ten months of using it has been like
The kit went on with a 50,000-rated cooler. The hose that came with the cooler was long enough to reach and big enough to fit, so I used it. For the cooler itself I used the plastic compression clamps they come with — simple, nothing exotic.
The cooler is heavier than you would expect hanging off the radiator, so I put four clamps on it instead of two, spread across the core to hold it steady.
The temperature change is the part I actually care about. The car used to climb past 200°F and just hover there. Now the transmission sits in the 160s and 170s and tops out around the 180s, and the fluid stays cold. That matters more on my car than most, because the converter locks up at 3,000 RPM and that is a heat source you cannot tune out. The cooler and these fittings are what fixed it.
Fitment was a non-event. They went on everywhere without modification, no cross-threading, no fighting. That is exactly what you want from a twelve-dollar part.
What I’d change
Nothing about the fitting — the thing I would change is on the other end of it. Plain rubber hose, the cheap stuff, is not hydraulic hose or PTFE braided, and over time weather and heat and driving will have it wanting to weep. I expect to get somewhere around five to ten years out of it before that starts. I went with the regular hose because I can always fix it later, and honestly I probably will. If you are doing this once and never touching it again, protect the hose from heat and abrasion, or spend the money on the PTFE steel-braided line up front.
Key specs
| Spec | Detail |
|---|---|
| Fitting type | Male 5/8″-18 inverted flare → 3/8″ hose barb |
| Material | Brass, two fittings per kit with O-rings |
| Hose size | 3/8″ inside diameter |
| Tightening | 11–15 ft-lb, thread sealant recommended |
| Listed fitment | GM applications and 1987-and-earlier Jeep (Hayden) |
| Sealant | Teflon tape or suitable thread sealant on the threads |
Who should skip it
Skip these if you do not want to run rubber hose at all. If the goal is a genuinely clean setup — the kind where people look at your engine bay and ask who did the work — go AN-6 instead: AN-6 fittings, AN-6 hose, and whatever adapter your cooler needs, making sure it is AN-6 compatible or threaded so you can screw on whatever end you want. That is a better result and a bigger project. These are for the “I don’t have time for this, let’s move” build. That was mine.
Frequently asked questions
Will the Hayden 390 fit a 1998 Corvette?
It fit mine. The kit is a 5/8″-18 inverted flare male fitting that screws into the stock GM cooler port and gives you a 3/8″ hose barb on the other end. Mine has been on since January 2022 with no leaks. Hayden lists the kit for GM applications generally, and 1987-and-earlier Jeep — check your thread before ordering.
What size hose goes on these fittings?
3/8″ inside diameter. That is the same size as the hose most transmission cooler kits ship with, which is why mine worked with the hose that came in the box. Clamp it properly and check it after the first few heat cycles.
Will it start leaking again eventually?
The fitting itself, probably not. The hose, likely — eventually. Cheap rubber hose degrades from heat and weather, and mine is still dry but I am not expecting that to last forever. PTFE braided line is the permanent answer.
Bottom line
If you are plumbing an auxiliary transmission cooler into a GM car and you want it done today, clean, and without an AN assembly session, these two brass fittings are the whole job. Nearly five years, still dry, and the transmission runs 30-odd degrees cooler than it did before.